Download

H8922 Industrial Dual SIMS Cellular Router FAQ

Hongdian Anatel IPV6 setting
 
About ICMP IPV6 settings
 
1. The PC system should be set the IP to IPV6
 
2. Hongdian router also needs to be set, the setting steps:
 
2.1 After entering 192.168.8.1 in the browser, set the modem protocol to IPV6, as shown in the figure
 

 

2.2 Set the LAN port IP to IPV6 IP

 

 

2.3 Set the Network type to modem, as shown below

 

How to check the device before returning to Hongdian

 

Hongdian FAQ Document

NO

 

Final review date

 

Title

How to check the device before returning to Hongdian

Attribute

Reset

Keyword

Reset

Submitter

 

First trial

 

Final review

 

This document is based on FW xxx(V7.2.0_SE) and higher

 

Summary

This document provides the instruction on how to check the device before returning to the Hongdian

 

Steps

1. The computer RJ45 network port is connected to the LAN port of the hongdian device using a network cable.

2. Make sure the computer is on the same network of the default router network (192.168.8.1/24). It’s highly suggested to disable WiFi on the computer.

3. After the computer has set the IP address, you can enter 192.168.8.1 in the browser and enter the account admin/admin

 

4.Check the firmware,make sure the firmware is latest.regarding the latest firmware, please confirm with the

engineers of Hongdian.

 

 

5.Reset the deivce ,Click---System---Files---Load

 

 

6. After reset, please reconfigure the router. if still can't get the device online, please contact Hongdian engineers.

How to config the modem

 

Hongdian FAQ Document

NO

 

Final review date

 

Title

How to configure Modem

Attribute

Modem APN

Keyword

APN

Submitter

 

First trial

 

Final review

 

This document is based on FW xxx(V7.2.0_SE) and higher

 

Summary

This document provides the instruction on how to config the router modem

 

Steps

1. The computer RJ45 network port is connected to the LAN port of the hongdian device using a network cable.

2. Make sure the computer is on the same network of the default router network (192.168.8.1/24). It’s highly suggested

to disable WiFi on the computer.

3. After the computer has set the IP address, you can enter 192.168.8.1 in the browser and enter the account

admin/admin

 

4.Click---Network---Modem---Mod

 

 

5. “Modem” Parameter instruction

 

 

6.Check the modem status.Status---Modem,it means dial successfully if modem status display “connected”.

 

How to configure and use DNAT

 

Hongdian FAQ Document

NO

 

Final review date

 

Title

How to configure and use DNAT

Attribute

DNAT

Keyword

NAT\DNAT

Submitter

 

First trial

 

Final review

 

This document is based on FW (V7.2.0_SE) and higher

 

Summary

DNAT is used to replace the destination address of packets accessing external network, router will replace the destination address of packet accessing external network into the user custom settings.

Through the DNAT function, we can remotely access the server on the LAN side of the router to solve the problem that the server does not have a public IP address

 

Network topology(Simple network or configuration can have no this)

Problem analysis or configuration steps

Step 1 Log-on WEB GUI of 3G/4G router.

      1、The computer RJ45 network port is connected to the LAN port of the hongdian device using a network cable.

      2、Download the required firmware to the local hard drive.

      3、Make sure the computer is on the same network of the default router network (182.168.8.1/24). It’s highly

suggested to disable WiFi on the computer.

 

      4、After the computer has set the IP address, you can enter 192.168.8.1 in the browser and enter the account

admin/admin

 

Step 2 Click “Forward > NAT” to open “NAT” tab.

 

 

Step 3 Click “Add” to add a new NAT rule.

 

 

Step 4 Select “DNAT” in NAT Type, to configure DNAT rule parameter.

 

Step 5 Single click “save” icon to finish.

 

 

Notes:The SIM card need get the public IP address 

 

How to configure the WiFi repeater

 

Hongdian FAQ Document

NO

 

Final review date

 

Title

How to configure the WiFi repeater

Attribute

WiFi repeater

Keyword

WiFi

Submitter

 

First trial

 

Final review

 

This document is based on FW xxx(V7.2.0_SE) and higher

 

Summary

This document provides the instruction on how to config the router WiFi station

 

Steps

1. The computer RJ45 network port is connected to the LAN port of the Hongdian device using a network cable.

2. Make sure the computer is on the same network of the default router network (192.168.8.1/24).

3. After the computer has set the IP address, you can enter 192.168.8.1 in the browser and enter the account

admin/admin

 

4.Disable DHCP server Click---Network---DHCP server--,”DHCP server” select “disable”.

 

 

5.Click---Network---WLAN,Wireless mode select repeater.

 

 

6.Select the access point you want to connect.in this guide,i select AIRPORT@#$_&-*

  Click ---connect,fill the WPA share key.

 

 

7.Check the WLAN repeater status.click---status---WLAN.

 

 

How to Import & Export the Configuration File

 

Hongdian FAQ Document

NO

 

Final review date

 

Title

How to Import & Export the Configuration

Attribute

Configuration file

Keyword

Configuration

Submitter

 

First trial

 

Final review

 

This document is based on FW H8922_V7.2.0_SE and higher

 

Summary

This document provides the instruction on how to import and export the configuration file.

 

Steps

1. The computer RJ45 network port is connected to the LAN port of the hongdian device using a network cable.

2. Make sure the computer is on the same network of the default router network (192.168.8.1/24). It is highly suggested to disable Wi-Fi on the computer.

3. After the computer has set the IP address, you can enter 192.168.8.1 in the browser and enter the account admin/admin

4. Export and Import the configuration file.

 

Export

Path: System->Files->Backup Setting

Step 1 Input a Key for encrypting the configuration file. (optional)

Step 2 Click “Export” button to generate a configuration file and download it to your computer.

 

Note: If a key is entered while exporting, the configuration file will be encrypted, please make sure the key is well

protected and memorized, it is necessary for configuration importing.

 

Import

Path: System->Files->Backup Setting

 

 

Step 1 Click “Choose” button to select the configuration file from local disk

Step 2 Input the key of the configuration file (if there is any).

Step 3 Then click “Import” button to apply the configuration from the file.

 

 

End

 

How to Setup a Remote Desk Help Environment

 

Hongdian FAQ Document

NO

 

Final review date

 

Title

How to Setup a Remote Desk Help Environment

Attribute

Asking for help

Keyword

Remote Assist

Submitter

 

First trial

 

Final review

 

This document is based on FW H8922_V7.2.0_SE and higher

 

Summary

This document provides the instruction on how to use TeamViewer/AnyDesk software for building a remote access

environment between customer and our support team.

 

Steps

 

1. The computer RJ45 network port is connected to the LAN port of the hongdian device using a network cable.

 

2. Make sure the computer is on the same network of the default router network (192.168.8.1/24).

 

3. Make sure your computer is connected to the internet via another gateway except the router itself, because we might

be going to with a network issue of the router.

 

4. Download the latest version of TeamViewer/AnyDesk software from the below link:

https://www.teamviewer.com/

https://anydesk.com/

 

5. Run the software on your computer.

TeamViewer

Step 1 Run the software on your computer, copy your TeamViewer ID and Password and send it to our support team.

 

Note: you can also create new random password or set a personal password by clicking the refresh button.

 

 

AnyDesk

 

 

 

Step 1 Run the software on your computer, click “Set password for unattended access” to setup a password for the

remote access

Step 2 Copy your Address and password and send it to our support team.

 

 

 

End

 

 

 

Link Backup-WLAN_Modem V1.0

 

 

Contents

 

Contents 2

Revision History 2

1 Overview 3

2 Description 3

 

Revision History

 

Updates between document versions are cumulative. Therefore, the latest document version contains all updates

made to previous versions. 

Doc Version

Product

Release Data

Details

V1.0

Hongdian Router

2017.08.21

First Release

1 Overview

Hongdian 3G/4G Router provides WLAN/Modem link backup for the field application which may need the WLAN

connection as main link,and the 3G/4G wireless connection as backup link, so as to make sure the stable connection.

Here we introduce the settings that WLAN link as main, modem link as backup. The converse of mainand back link is

also OK.

2 Description 

 

1. We finish the settings about wlan and modem, make wlan and modem both connecting,wlan setting as below

show , modem port is according to your custom.

WLAN:

 

 

Modem:

 

 

2. If your Network Type settings has changed, please recover to the following.

 

 

3. We use Link Backup feature, as following:

 

 

Main link.

 

Rule0 is for checking eth1, if wlan link fail, the link will switch to backup link.

 

 

Note: If don’t want backup link switch to main link immediately when main link is back, can setup the Running Timeout

setting. The time means unless the main link works for that specific time, link should not switch back to

 

 

 

Rule1 is for checking modem, When Main link is back, the link will switch to main link. 

 

 

4. We add MASQ about eth1 and modem.

 

 

Please delete the default setting in page>>Forward>>Routing. When using link backup feature, this setting should be

empty. 

 

After that, the link backup setting is done, you will see the default route is eth1, refer to pic1, if wan link fail, the link will

switch to modem link, you will see the default route is modem, refer to pic2

 

pic1

 

 

pic2

 

 

PS: about the linkbackup total switch time instruction:

 

 

From the log, the linkbackup switch from start to end, total cost 15s(retry time is 3), so every linkbakcup every check

time cost 5s, we can draw the linkbakcup total switch time range is

 

Min: 5s*retry time<= linkbackup total switch time <= Max: normal interval+5s*retry time

 

Module info&version_module AT

 

Module AT Command Operation Instructions

Overview

This document mainly introduces how to enter the module AT mode and execute the module's AT command

 

Steps:

1. Enter 192.168.8.1 in the browser, username admin, password admin

2. Click "Network---modem" to disable the modem

 

 

3. Use SSH or putty software to log in to the device, the telnet command is telnet 192.168.8.1 5188, the account is root,

and the password is superzxmn

4. Enter cat /tmp/modem.dev view module interface

 

 

5. Enter module AT mode: enter tip /dev/ttyUSB2, then enter ATE1, and press Enter.

6. The AT command of the module version information is ATI

 

 

Enable modem after executing AT command

 

 

Upgrade for RouterU

 

Summary

This document provides the instruction on how to upgrade Hongdian Router

 

Steps

1. The computer RJ45 network port is connected to the LAN port of the hongdian device using a network cable.

2. Download the required firmware to the local hard drive.

3. Make sure the computer is on the same network of the default router network (182.168.15.1/24). It’s highly

suggested to disable WiFi on the computer.

4. After the computer has set the IP address, you can enter 192.168.15.1 in the browser and enter the account

admin/admin

 

 

5. Click System ---> Files, and click the Browse button to choose the boot/app then click the Upgrade button:

 

upgrade app(H8959V10_APP_V7.2.0_SE__2006050540.trx)

 

 

Around 3 minutes, the web shall show “Upgrade is ok”.

 

 

6. After reboot completes

Focusing on IoT market , helps customers improve the capability of decision-making and controlling

Contact an Hongdian expert and get started today!